Electromagnetic flowmeter for standard applications with abrasive and aggressive liquids

  • Chemically resistant, for liquids (>5 μS/cm) with solid content (≤10%)
  • Up to +180°C / +356°F
  • Flange: DN2.5…1200 / ⅒…48", max. PN40 / ASME Cl 300
  • 4…20 mA, pulse, frequency, status, HART®

OPTIFLUX 4100 C – Compact version

OPTIFLUX 4100 C Electromagnetic flowmeter – Compact version

The OPTIFLUX 4100 is an electromagnetic flowmeter (EMF) for a wide range of standard process applications with aggressive and abrasive liquids. It enables reliable flow measurement even under harsh process conditions with temperatures up to +180°C / +356°F, low conductivity (≥5 µS/cm) and solid content (up to 10%). This makes the flowmeter particularly suitable for applications involving corrosive chemicals, sewage and drilling mud or mining sludge. Installation in measurement chambers subject to (constant) flooding is also possible using the optional IP68 / NEMA 6P rated version.

Unlike the basic version OPTIFLUX 4050, the OPTIFLUX 4100 features higher accuracy. It comes with a selection of chemically resistant liners and electrodes. Due to its full bore design without moving or intruding parts, there is no pressure loss and no maintenance required. A full on-site verification of the flowmeter without process interruption can be carried out using the OPTICHECK service tool.

Product highlights

  • Bi-directional flow measurement over a wide dynamic range (turndown ratio: 1000:1)
  • PTFE, PFA, ETFE, hard rubber, soft rubber or PU liner: excellent chemical and abrasion resistance
  • Wide range of electrode materials
  • Special designs, sizes, inner diameters and liner thicknesses on request
  • Standard measurement accuracy: ±0.3% or ±1mm/s of measured value (MV)
  • Optional external coatings for offshore or subsoil installation (also acc. to ISO 12944)
  • Diagnostics incl. conductivity, electrode error, ambient and process temperature etc.
  • Full bore design: No moving parts, no wear, no pressure loss
  • For hazardous areas: ATEX, IECEx, FM, CSA
  • On-site verification of flowmeter with OPTICHECK service tool

Typical applications


  • Standard applications with clean, aggressive or abrasive liquids

Chemical and other process industries

  • Conductive fluid chemicals
  • Process water, cooling water

Oil and gas industry

  • Water injection (high pressure)
  • Drilling mud
  • Produced water

Minerals and mining industry

  • Hydrocyclone feed lines

Pulp and paper industry

  • Chemicals (black liquor, bleach, etc.)

Wastewater industry

  • Irrigation
  • Sludge and sewage treatment

Accessories for this product


Handheld for in-depth verification, device commissioning and monitoring

  • On-site performance check and verification (level 0,1,2) without process interruption
  • Convenient commissioning of field devices, e.g. zero calibration
  • Detailed reports for proof test documentation of safety loops acc. to IEC 61508/61511, and for quality management systems (ISO 9001)

View product details


DTM for advanced device verification and commissioning

  • Usable with any FDT frame application from the control room or on site
  • Advanced verification (level 0,1) without process interruption
  • Detailed reports for proof test documentation of safety loops acc. to IEC 61508/61511, and for quality management systems (ISO 9001)

View product details

Related products

IFC 100

Electromagnetic flow converter for combination with OPTIFLUX and WATERFLUX flow sensors

  • Compact and wall-mounted housing
  • With many sensor and process diagnostics for standard requirements
  • 4-wire, 4…20 mA, pulse, frequency, status, HART®

View product details


Electromagnetic flow sensor for combination with IFC 050, IFC 100, IFC 300 and IFC 400 signal converters

  • Full bore design: pipe cross-section without restrictions
  • Connection sizes: DN2.5…3000 / ⅒…120" (depending on signal converter)
  • Liner: PTFE, PFA, ETFE, PU, hard and soft rubber

View product details